Voltage optimisation for business

Voltage optimisation: does a voltage optimiser cut your bill? Costs, savings and the sites it suits

UK mains is supposed to be 230V, but the law lets it run as high as 253V, and many sites see 240V or more all day. A voltage optimiser trims that back so some of your equipment draws less power. On the right site, with old lighting and fixed-speed motors, the saving is real. On a site already full of LED lights and variable-speed drives, it can be close to nothing. Here's how to tell which you are before you spend a penny.

Updated 20 November 2026 · Independent guide, not the government's Great British Energy (gbe.gov.uk) · Checked against GOV.UK, Ofgem and scheme sources

230VThe UK's declared supply voltage
Up to 253VWhat the rules allow (+10%), and many sites run high
~15%Theoretical cut on a voltage-dependent load going from 240V to 220V
0%Saving on LED lighting: it draws the same power at any voltage
Business, farm, school or charity? You're in the right place. Looking for help with a home? Check home energy grants →

Voltage optimisation: key facts for 2026

What it isA transformer fitted after your main meter that lowers the voltage reaching your equipment to a steadier, lower level, typically around 220V.
Why it can workUK low-voltage supply is declared at 230V but allowed to range from 216.2V to 253V. Many sites run in the 240s, which makes some equipment use more power than it needs.
What savesVoltage-dependent loads: old fluorescent tubes with magnetic ballasts, sodium and metal halide high bays, and lightly loaded fixed-speed motors on fans, pumps and compressors.
What doesn'tLED lighting, electronic-ballast fittings, motors on variable-speed drives and IT equipment. They draw the same power whatever the voltage, and some draw more current.
GrantsNo GB-wide grant. In Northern Ireland, NISEP's Commercial Energy Saving Scheme lists voltage optimisation at a 20% grant, with the next round expected April 2027.
TaxPart of your electrical system, so treat it as special-rate plant. The £1 million Annual Investment Allowance can still write the cost off in year one.

How voltage optimisation works

Electricity in Great Britain is supplied at a declared 230V. Under regulation 27 of the Electricity Safety, Quality and Continuity Regulations 2002, your network operator can let it drift 10% above or 6% below that, so anywhere from about 216V to 253V is legal. Most equipment sold in Europe is designed to run happily at 220V to 230V.

The legal supply band
Declared at 230V, allowed from 216.2V to 253V
Legal UK low-voltage range216.2V to 253V
10% above or 6% below 230V (marker).
What most equipment is designed for220V to 230V
Where many sites runthe 240s
216.2V253V
Cutting a site from 240V to 220V could in theory save about 15% on voltage-dependent loads; LED lighting saves nothing.

A voltage optimiser (also called a voltage optimisation unit, voltage management or voltage reduction) is a transformer installed between your main incomer and your distribution boards. It brings the voltage down by a fixed amount, or holds it at a set point if it's an electronically controlled unit. Your equipment then runs at the voltage it was built for, not at whatever the grid happens to be sending.

The saving comes from physics. On a simple resistive or inductive load, power rises with the square of voltage. SEAI's verification guidance puts it plainly: cutting a site from 240V to 220V could in theory save about 15% on those loads. The catch is that only some loads behave that way.

Which equipment saves, and which doesn't

EquipmentSaves with voltage optimisation?Why
Fluorescent tubes with magnetic (wire-wound) ballastsYesPower falls as voltage falls. Light output can dip slightly
Sodium, mercury and metal halide high baysYesCommon in older warehouses and factories
Fixed-speed motors (fans, pumps, compressors)SometimesOnly where the motor is oversized and lightly loaded. A 10% voltage cut reduces torque by about 19%, so a fully loaded motor can overheat
Incandescent and halogen lampsYesRare on commercial sites now
LED lightingNoLED drivers draw the same power at any voltage
Fluorescents with electronic ballastsNoThe ballast regulates its own output
Motors on variable-speed drivesNoThe drive holds power constant and draws more current at lower voltage
IT, servers, chargers, modern electronicsNoConstant-power supplies. If they're 30% or more of your load, the circuits need checking for extra current
Heaters, ovens, kettlesNot reallyThey draw less power but run longer to reach the same temperature, so the energy used barely changes

The rule of thumb: the older your lighting and the more fixed-speed motors you run, the better voltage optimisation looks. If you've already done a full LED retrofit and fitted drives to your big motors, put the money into solar or battery storage instead.

Is voltage optimisation worth it? A quick test

Answer these five questions before you take a sales call. Three or more "yes" answers and a proper survey is worth your time.

  1. Is your incoming voltage high? A logger on your main board for a week will show it. Sites regularly above 240V have the most to gain. Sites already around 230V have very little.
  2. Do you still have fluorescent or high-bay lighting? Old tubes with magnetic ballasts and sodium high bays are the biggest winners.
  3. Do you run fixed-speed motors for long hours? Ventilation fans, pumps, refrigeration and compressors that run without drives.
  4. Is your electricity spend large? A single-digit percentage saving needs a big bill to pay back a transformer and an installation.
  5. Are you staying put? A voltage optimiser is a fixed asset. Payback depends on years of savings at the same site.

Be wary of anyone quoting a saving before they've logged your voltage and listed your loads. A good installer measures first, models the saving on your actual equipment, and agrees how the saving will be verified afterwards with metering, not with a brochure figure.

What voltage optimisation costs

Price depends on the size of your supply, not the size of your building. The unit is sized in kVA to match your incoming supply and maximum demand, and a three-phase commercial unit needs a shutdown to install, usually out of hours. What goes into the quote:

  • The unit itself, sized to your supply capacity (kVA), with a bypass so the site can run if it's ever taken out of service.
  • Fixed or electronic regulation. Fixed-ratio units are simpler and cheaper. Electronically regulated units hold a set voltage however the grid moves, and usually cost more.
  • Installation: the shutdown, cabling between the incomer and your boards, and any space or ventilation the unit needs.
  • Logging and verification: a week or more of voltage and load logging before, and metering after so you can see the saving.

Indicative prices and a worked payback

Business Energy Scotland, the Scottish Government-funded advice service, says typical installations range from £2,000 to £5,000. Large multi-hundred kVA units on industrial supplies cost more, so treat that as a guide for smaller commercial sites. BEAMA, the electrical manufacturers' trade body, puts average savings at around 13%, but that is an industry average across suitable sites, not a promise for yours.

Worked payback
Same £5,000 unit, two sites
Indicative
Site with 40% voltage-dependent load£2,000 a year · 2.5 years
After an LED retrofit (10% voltage-dependent)£500 a year · 10 years
Annual use 200,000 kWh. The 10% saving and 25p per kWh price are assumptions for the example. Typical installations range from £2,000 to £5,000.

Here's how to do the sum properly, applying the saving only to loads that respond. The 10% saving and 25p per kWh price are assumptions for the example, so swap in your own logged figures and tariff:

  • Annual use: 200,000 kWh
  • Voltage-dependent share (old lighting, fixed-speed motors): 40%, so 80,000 kWh
  • Saving on those loads at 10%: 8,000 kWh a year
  • At 25p per kWh: 8,000 x £0.25 = £2,000 a year
  • Payback on a £5,000 installation: 5,000 / 2,000 = 2.5 years

Now run the same site after an LED retrofit has taken the voltage-dependent share down to 10%: 20,000 kWh x 10% = 2,000 kWh, or £500 a year, and the payback stretches to 10 years. That's why the order you do things in matters.

Ask for the price, the predicted annual kWh saving on your loads, the payback in years, and how the saving will be measured. If the installer won't commit to the last one, keep looking.

On tax, a voltage optimiser forms part of your building's electrical system. HMRC treats electrical systems as integral features, which are special-rate plant, but the £1 million Annual Investment Allowance can still write the full cost off against profits in the year you buy it. Check the detail with your accountant.

Are there voltage optimisation grants?

There is no national voltage optimisation grant in England, Scotland or Wales in 2026. The routes that can help are:

  • Northern Ireland: NISEP. The Commercial Energy Saving Scheme lists voltage optimisation among its measures, at a 20% grant with 80% paid by the business. Power NI runs it. The 2026/27 round has closed for applications, and the next is expected in April 2027, subject to funding. See Northern Ireland business energy grants.
  • Scotland: SME Loan. Business Energy Scotland says voltage optimisation is eligible for funding through its SME Loan Scheme. Check whether your project qualifies on our Business Energy Scotland page.
  • Wales: Green Business Loan Scheme. The Development Bank of Wales lends for energy-saving projects. See Welsh business energy grants and loans.
  • Local council funds. Some councils part-fund energy-saving capital projects identified in an energy survey. See local council business energy grants.

Every other route is about tax and bills: the Annual Investment Allowance, and a lower electricity bill that starts the day it's switched on. A free business energy audit will usually tell you whether voltage optimisation ranks above LED, drives or solar on your site.

How a voltage optimisation survey should work

A credible saving figure comes from measurement on your site. A good survey has four parts:

  1. Voltage and load logging. A three-phase power quality logger on the main incomer for at least a full working week, weekend included. It records voltage on each phase, current, kW, power factor and harmonics. You want the average, the minimum and when the peaks happen, because the lowest voltage sets how far the unit can safely step down.
  2. A load inventory. Walk the site and list what's on each board: lighting type and ballast, motors with and without drives, refrigeration, IT, heating. This splits your consumption into the loads that save and the loads that don't. A site where most of the kWh are LED and drives can be ruled out at this stage.
  3. A modelled saving on your loads. Apply the voltage reduction only to the voltage-dependent share of your consumption, not to the whole bill. Your half-hourly data from your supplier helps here.
  4. An agreed measurement plan. SEAI's verification guidance expects sub-metering or a before-and-after comparison, and BEAMA suggests three months of half-hourly data before and after, or repeated on/off tests with the unit switched in and out. Agree the method before you sign, so the saving is something you can check.

When voltage optimisation is a waste of money

The IET's verdict on voltage optimisation is "a qualified yes, but not for all types of load", and applied to the wrong site it can be a waste of money. Skip it, or at least don't buy it yet, if any of these describe your site:

  • Your lighting is already LED. LED drivers draw the same power whatever the voltage, so the lighting saving that sold voltage optimisation in the 2000s has gone.
  • Your big motors run on variable-speed drives. The drive already sets the motor's voltage and speed. Lowering the supply just makes the drive pull more current. If your fans and pumps don't have them yet, our variable speed drives guide shows how to work out that saving.
  • Your supply already sits near 230V. If logging shows a steady 228V to 232V, there's little to take off before you approach the 216V legal minimum at the far end of your cables.
  • Your load is mostly IT, heating or electronics. Offices, data rooms and heated spaces see little or nothing. The Ministry of Defence's practitioner guide warns that constant-power equipment draws more current at lower voltage, and protective devices can trip.
  • You're planning an LED or drives upgrade anyway. Do those first. They usually save more, and they shrink the voltage-dependent load the optimiser relies on.
  • You're leaving the site in a year or two. A transformer bolted into your switchroom stays with the building.

For a site like this, the money usually works harder in LED lighting, rooftop solar or a full energy audit that finds the real waste.

Voltage optimisation with solar panels and batteries

Solar raises voltage. When an array exports, its inverters push the voltage up at your connection point, and an inverter will trip off if voltage rises above its protection limit. On a site that already runs high, that can cost you generation on sunny days. Where the inverters connect relative to the optimiser matters: upstream they see the full grid voltage, downstream they export back through the transformer. Neither is automatically right, so tell any installer about existing or planned solar so the wiring, the unit's position and the inverter settings are designed together. For large arrays on factory or warehouse roofs, the network operator reviews this in the G99 application.

Solar also shrinks the saving. Voltage optimisation saves a share of the kWh you import. Every kWh you generate yourself is one the optimiser no longer saves money on, so model the two together rather than adding their brochure savings.

Batteries don't change the voltage case much. Commercial battery storage saves money by shifting when you import and cutting peaks, not by changing how much power your equipment draws. It can sit alongside an optimiser, but it doesn't make one more or less worthwhile.

What to pair it with

  • Power factor correction. Sites with lots of motors often pay reactive power charges too. The same logger can measure power factor and voltage in one visit.
  • LED lighting. LED usually saves more than voltage optimisation on lighting, but it removes the voltage saving on those circuits. Do the sums together, not separately.
  • ESOS. Large companies have to audit their energy use every four years. If your assessor flags high site voltage, that's your evidence base for a survey.
  • Funding. Our business energy grants guide covers every national scheme, loan and tax relief in one place.

Sources checked 20 November 2026

Great British Energy is an independent guide. We are not affiliated with Great British Energy, the publicly owned energy company (gbe.gov.uk), HM Government, Ofgem or OZEV. Scheme rules and budgets change, so confirm the current position with the scheme administrator before you commit spend. We may receive a fee from the installer we introduce you to.

Voltage optimisation questions

What is voltage optimisation?

It's a transformer fitted after your main meter that lowers and steadies the voltage supplied to your equipment. UK supply is declared at 230V but can legally run up to 253V. Bringing it down towards 220V cuts the power drawn by voltage-dependent equipment such as older lighting and fixed-speed motors.

Does voltage optimisation really save money?

On the right site, yes. The saving depends on how high your incoming voltage is and how much of your load is voltage-dependent. Old fluorescent and high-bay lighting and lightly loaded fixed-speed motors save. LED lighting, variable-speed drives and IT equipment don't. Log your voltage and list your loads before you believe any saving figure.

Is voltage optimisation worth it with LED lighting?

Usually not for the lighting. LED drivers draw the same power at any voltage, so a site that is all LED loses most of the lighting saving. It can still pay if you run many fixed-speed motors at high voltage, but measure first.

How much does a voltage optimiser cost?

Business Energy Scotland says typical installations range from £2,000 to £5,000, with large industrial units costing more. The price depends on your supply capacity in kVA, whether the unit is fixed or electronically regulated, and how hard the installation is. Get a quote that shows the predicted kWh saving on your actual loads, the payback in years, and how the saving will be metered afterwards.

Is there a grant for voltage optimisation?

Not in Great Britain. In Northern Ireland, NISEP's Commercial Energy Saving Scheme lists voltage optimisation at a 20% grant through Power NI; the 2026/27 round has closed and the next is expected in April 2027. Scotland's SME Loan and the Welsh Green Business Loan Scheme can fund energy-saving projects, and the £1 million Annual Investment Allowance can write off the cost.

Can voltage optimisation damage equipment?

Lowering voltage within the legal range is normally safe, but a fully loaded fixed-speed motor loses torque faster than voltage falls and can overheat, and constant-power equipment draws more current. A proper survey checks motor loading and circuit capacity before anything is fitted.

Get your site quoted properly

Two minutes now saves weeks of ring-rounds. Tell us about your site and we will introduce one suitable installer.

Get a free voltage optimisation check →
Get a free voltage optimisation check →