Commercial boilers for UK businesses

Commercial boilers: replace it right in 2026, cut the gas bill and check the grants

A commercial boiler usually gets replaced in a hurry: it fails in January, the building is cold and the first quote gets signed. That is the most expensive way to do it. This guide covers the decision properly: when to repair and when to replace, how to size the new plant, what drives installation cost, the efficiency and controls a replacement must meet under Part L, the legal gas safety duties, and how to compare running costs against a heat pump using your own gas and electricity prices.

Updated 20 November 2026 · Independent guide, not the government's Great British Energy (gbe.gov.uk) · Checked against GOV.UK, Ofgem and scheme sources

91%Minimum seasonal efficiency for a replacement gas boiler up to 400kW (Part L)
100kWBoiler output above which optimum start/stop and staged firing are expected
£7,500Boiler Upgrade Scheme grant if you swap to a heat pump up to 45kWth
£1mAnnual Investment Allowance to write the cost off
Business, farm, school or charity? You're in the right place. Looking for help with a home boiler? Check home energy grants →

Commercial boilers: key facts for 2026

Efficiency ruleIn England, a new gas boiler up to 400kW in an existing building should reach 91% seasonal efficiency (gross). 401kW to 2MW: 88%. Above 2MW: 84% (Approved Document L Vol 2, Table 6.2).
Controls ruleBoiler systems over 100kW should have optimum start/stop and either high/low firing or sequenced multiple boilers. Gas boilers over 500kW should have fully modulating burners.
Like for likeA replacement on the same fuel must be no less efficient than the old one. A switch of fuel must not raise CO2 or primary energy per kWh of heat.
New buildingsThe Future Buildings Standard expects new non-domestic buildings to meet heating and hot water from low-carbon sources. It comes into force on 24 March 2027.
Gas safetyEmployers must keep gas appliances, pipework and flues at their workplace in a safe condition, using Gas Safe registered engineers.
GrantsThere is no grant for a gas boiler. The Boiler Upgrade Scheme pays £7,500 towards a heat pump up to 45kWth in a business building in England or Wales.

Commercial boiler replacement: repair or replace?

Most commercial boilers are replaced because one fails, not because anyone planned it. If you have any warning at all, use it. The questions that decide repair versus replacement are practical ones:

  • Age and parts. Once a manufacturer stops supplying parts for a model, every breakdown gets slower and dearer to fix. Ask your service engineer whether parts are still available and how long for.
  • Breakdown history. Repeated call-outs for the same fault (heat exchanger leaks, ignition faults, failed fans) usually mean the boiler is near the end.
  • Efficiency. Older non-condensing boilers sit well below today's minimums. Part L asks a replacement gas boiler up to 400kW to reach 91% seasonal efficiency, so the gap between your old boiler and that figure is gas you are paying for and not using.
  • Safety findings. If a Gas Safe engineer classes a boiler or flue as unsafe, the decision is made for you.
  • Your plans for the building. If you intend to move to a commercial heat pump within a few years, a big repair can buy time while you plan the switch properly. A brand new gas boiler locks the building into gas for the boiler's whole life.

Public sector funding gives a useful benchmark for "end of life". The Public Sector Decarbonisation Scheme requires the building to be served by fossil fuel heating "at the end of its useful life", which Salix says "is generally 10 years or older". That is a funding rule, not a law about boilers, but it shows where the public sector draws the line.

Plan before it fails. A boiler replacement done in summer, with time for a heat-loss survey and two options priced, almost always comes out cheaper than an emergency swap in winter. If your boiler is over ten years old, get it surveyed now.

Commercial gas boilers and other options

OptionWhere it fitsWhat to know
Condensing gas boilers (wall-hung or floor-standing)Most offices, schools, churches, care homes and shops on mains gasOnly condense, and hit their rated efficiency, when the return water is cool enough. Old radiator systems run hot may need lower flow temperatures and weather compensation.
Modular cascade (several smaller boilers)Larger or variable loads; buildings that can't be left without heatSequence control runs one boiler at a time at low load and keeps heat on if one fails. Part L accepts sequenced multiple boilers as the staged control for systems over 100kW.
LPG or oil boilersOff-grid sitesPart L sets 93% for a replacement LPG boiler up to 2MW and for a single oil boiler. Off-grid buildings get the biggest heat pump grant (see below).
Biomass boilersRural, off-gas sites with fuel storage and accessEligible for a £5,000 Boiler Upgrade Scheme grant only if the property is off the gas grid and in a rural location.
Electric boilersSmall loads, or where gas is unavailableSimple, but every kWh of heat costs a kWh of electricity. Part L covers them in a separate subsection.
Heat pumps or a hybridBuildings that can run at lower flow temperatures, or where the boiler is kept for peak daysA heat pump delivers several kWh of heat per kWh of electricity. A hybrid (heat pump plus gas boiler) isn't eligible for the Boiler Upgrade Scheme.

Steam boilers, used in some factories, laundries and hospitals, sit outside the Part L boiler guidance altogether. For process heat, see industrial heat pumps.

Sizing a replacement commercial boiler

The fastest way to waste money on a replacement is to copy the nameplate of the old boiler. Many existing boilers were oversized when fitted, and the building has often had insulation, new windows or a change of use since. An oversized boiler cycles on and off, spends its life at low load and costs more to buy.

Part L's own maths shows why part load matters. The seasonal efficiency it uses for commercial boilers is 0.81 × efficiency at 30% load + 0.19 × efficiency at 100% load. In other words, the guidance assumes a boiler spends most of its working time well below full output. Sizing it close to the real peak, with good part-load performance, is where the efficiency comes from.

A sense check you can do from your bills

  1. Take a year of gas use for heating and hot water from your bills, in kWh. If gas also feeds kitchens or processes, take those out.
  2. Multiply by the old boiler's efficiency to get the heat the building actually used. If you don't know the efficiency, ask the engineer to estimate it from the boiler's age and type. Part L's Appendix E gives a hierarchy for working out the seasonal efficiency of existing boilers.
  3. Ask the installer for a room-by-room heat-loss calculation that gives a design peak in kW. Divide your annual heat figure by that peak. The answer is the number of hours a year the boiler would need to run flat out to deliver your annual heat.
  4. If that number looks very low for a building heated most of the year, the proposed boiler is probably oversized. Ask the installer to explain it.

This is a check on the quote, not a design method. The design has to come from a proper heat-loss survey, and the same survey is what any heat pump option will need, so get it done once and use it for both.

Commercial boiler efficiency rules: what a replacement must meet

In England, a replacement boiler must meet Approved Document L Volume 2. The guidance applies to "wet central heating systems that use commercial boilers fired by natural gas, liquid petroleum gas, oil or biomass". Here are the minimum seasonal efficiencies (gross calorific value) for boiler plant installed in existing buildings, from Table 6.2:

FuelSystemMinimum seasonal efficiency
Natural gasSingle boiler up to 400kW91%
Single boiler 401kW to 2MW88%
Single boiler over 2MW84%
Multiple boilers84% for any one boiler, 91% for the whole system
LPGSingle boiler up to 2MW93%
Single boiler over 2MW88%
Multiple boilers88% for any one boiler, 93% for the whole system
OilSingle boiler93%
Multiple boilers88% for any one boiler, 93% for the whole system

Controls. Boiler systems with an output over 100kW should have optimum start/stop control (with night setback or frost protection outside occupied hours) and either two-stage high/low firing or multiple boilers with sequence control (para 6.7). Gas boilers and multi-stage oil boilers over 500kW should have fully modulating burners (para 6.8). When a boiler is replaced, each room should get thermostatic room controls, or zone controls where that's justified (para 5.14). Weather compensation is expected "where appropriate and technically feasible". For larger sites, a building management system is usually how these controls are delivered.

Like for like. Para 5.4 says a replacement must be at least as efficient as the Section 6 minimum and, on the same fuel, no less efficient than the boiler it replaces. Changing fuel is allowed if the new system produces no more CO2 and has no higher primary energy demand per kWh of heat. Part L's own worked example passes an 85% oil boiler replaced by a 93% LPG boiler on both tests.

Ecodesign. Separately from Part L, the GB ecodesign rules (Regulation 813/2013 as it applies here) cover boilers up to 400kW placed on the market. Between 70kW and 400kW a fuel boiler must reach 86% useful efficiency at full output and 94% at 30% load, and gas boilers must emit no more than 56 mg of nitrogen oxides per kWh of fuel. Meeting these limits is the manufacturer's job, but ask for the product data sheet with the quote.

What changes in 2027

The 2026 edition of Approved Document L Volume 2 takes effect on 24 March 2027 for most building work in England. For boilers in existing buildings, it keeps the same efficiency table and the same 100kW and 500kW controls wording.

The big change is for new buildings: under the Future Buildings Standard, the government's consultation said "all heating and hot water demand should also be met through low-carbon sources", and Building Circular 01/2026 says new non-domestic buildings will be "built with low carbon heating".

The March 2026 government response keeps room for "fossil fuel backup heating systems in new non-domestic buildings such as hospitals and community centres". Projects with a building notice or full plans application in before 24 March 2027 keep the old rules if work starts before 24 March 2028.

So in 2026 you can still replace a gas boiler with a gas boiler in an existing building. What has changed is the direction: gas is being designed out of new buildings, and the tax on gas is rising faster than the tax on electricity (see running costs below).

Scotland, Wales and Northern Ireland have their own building regulations and technical guidance. Check the local rules before you sign a quote. The gas safety and ecodesign rules on this page apply across Great Britain.

Commercial boiler installation cost: what drives the price

There is no official price list for commercial boiler work, and the bare figures quoted around the web don't tell you much about your building. The boiler itself is often a minority of the bill. These are the lines that move a quote:

  • Boiler output and number of boilers. One large boiler or a cascade of smaller ones, plus any spare capacity for resilience.
  • Flue. Reusing an existing chimney, lining it, or running a new flue through the building. A condensing boiler also needs a condensate drain.
  • Plant room work. Low-loss header or plate heat exchanger, pumps (ideally variable speed, see variable speed drives), pressurisation unit, valves and pipework alterations.
  • System cleaning. Part L expects the heating circuits to be "thoroughly cleaned and flushed out" before a new heating appliance goes in, with inhibitor added. Old systems full of sludge can need a lot of work.
  • Controls. Optimum start/stop, sequence control, room or zone thermostats and weather compensation, or integration with an existing BMS.
  • Access and removal. Basements, rooftop plant rooms, cranes, and stripping out old cast-iron boilers. Asbestos surveys on older plant rooms.
  • Gas supply. Larger or extra boilers can need bigger pipework or a meter upgrade from the gas network.
  • Out-of-hours work and temporary heat. Schools, care homes and hotels often need a temporary boiler while the swap happens.
  • Building control and commissioning. Notification, combustion testing, commissioning records and handover.

How to compare quotes

  1. Ask every installer to price the same specification from the same heat-loss figure. A cheaper quote with a smaller flue job or no system flush is a different job.
  2. Ask for each line above separately, so you can see where the money goes.
  3. Ask for the seasonal efficiency of the proposed boiler against the Part L figure, and the controls it comes with.
  4. Ask for a heat pump or hybrid option priced on the same survey. Even if you choose gas, you'll know what the alternative costs.
  5. Work out the lifetime cost: installed price, minus tax relief and any grant, plus annual fuel and servicing, over the years you expect to keep it.

Gas boiler vs heat pump running costs: the method

The comparison everyone wants is simple to set up with your own numbers. You need four figures: your annual gas use for heating, the efficiency of your old and new boiler, your unit prices for gas and electricity (from your bills or contract, including the Climate Change Levy), and the seasonal efficiency (SCOP) the heat pump installer is designing to.

  1. Heat the building needs = annual gas kWh × old boiler efficiency.
  2. Gas for a new boiler = heat needed ÷ new boiler efficiency.
  3. Electricity for a heat pump = heat needed ÷ SCOP.
  4. Multiply each by its unit price and compare.

The quick test: a heat pump is cheaper to run than a gas boiler when your electricity price ÷ your gas price is less than the heat pump SCOP ÷ the boiler efficiency.

Worked example

The prices here are example inputs to show the arithmetic, not market rates. Use your own.

  • A school uses 300,000 kWh of gas a year for heating, through an old boiler we'll assume runs at 80%. Heat needed: 300,000 × 0.80 = 240,000 kWh.
  • Example prices: gas 6.0p/kWh and electricity 25.0p/kWh, each plus the Climate Change Levy of 0.801p/kWh that applies to both from 1 April 2026. That makes 6.801p and 25.801p.
  • New gas boiler at 91%: 240,000 ÷ 0.91 = 263,736 kWh of gas, costing about £17,940. Against the old boiler's 300,000 kWh (about £20,400) that saves about £2,470 a year.
  • Heat pump at an assumed SCOP of 3: 240,000 ÷ 3 = 80,000 kWh of electricity, costing about £20,640.
  • The quick test: 25.801 ÷ 6.801 = 3.79, against 3 ÷ 0.91 = 3.30. At these prices the new gas boiler is cheaper to run. With the same prices, a SCOP of about 3.5 tips it to the heat pump (break-even is 3.79 × 0.91 = 3.45); so does an electricity price below about 21.6p before the levy at a SCOP of 3.

Three things shift this sum in practice. Solar panels on the roof can supply some of the heat pump's electricity at well below grid price (see commercial solar panels). Lower flow temperatures and fabric improvements raise the SCOP. And the levy is moving against gas: GOV.UK's published rates are equal at 0.827p for both from 1 April 2027, then gas rises to 0.853p from 1 April 2028 while electricity stays at 0.827p. See the Climate Change Levy guide for exemptions and the reduced rates for climate change agreement holders. Charities using fuel for non-business purposes don't pay the levy.

Your half-hourly or monthly meter data, from half-hourly metering or your supplier, makes this far more accurate than a single annual figure.

Commercial boiler service and your legal gas safety duties

We don't service boilers, but anyone searching for a commercial boiler service should know what the law asks of them, because it decides who you can use and what records to keep.

  • Employers and the self-employed: regulation 35 of the Gas Safety (Installation and Use) Regulations 1998 makes it the duty of every employer or self-employed person "to ensure that any gas appliance, installation pipework or flue installed at any place of work under his control is maintained in a safe condition so as to prevent risk of injury to any person". The law doesn't set a fixed interval for this duty. HSE's advice is to make sure "your gas pipework, appliances and flues are regularly maintained", and annual servicing to the manufacturer's instructions is the usual way to show it.
  • Who can do the work: regulation 3 says nobody may work on a gas fitting unless competent, and businesses doing gas work must be in the class of persons approved by HSE, which in practice means Gas Safe registered. HSE notes that an engineer's ID card shows which appliances they are qualified to work on, so check the card covers commercial (non-domestic) work, not just domestic boilers.
  • Landlords of residential space: where people live in the building under a lease or licence, for example flats heated from a communal boiler, regulation 36 adds a duty to have each appliance and flue "checked for safety within 12 months of being installed and at intervals of not more than 12 months", and to keep the record. HSE warns not to assume an annual service covers everything a safety check requires.
  • Gas leaks: turn off the supply and call the National Gas Emergency Service on 0800 111 999 (for LPG, your LPG supplier).

A service visit is also the cheapest survey you'll get. Ask the engineer to note the boiler's age, combustion readings, parts availability and any faults, and you'll have most of what you need to plan the replacement.

Grants and tax relief for replacing a commercial boiler

There is no government grant for a new gas boiler in a business building. The funding goes to the low-carbon alternative:

  • Boiler Upgrade Scheme (England and Wales): GOV.UK says the grant can replace the heating in "a building used for your business".
  • What it pays: £7,500 towards an air or ground source heat pump, £5,000 towards a biomass boiler (off the gas grid and rural only) and £2,500 towards an air-to-air heat pump. Until March 2027 there's an extra £1,500 for air or ground source heat pumps where the property is heated by oil or LPG with no mains gas.
  • Who and what size: you must own the property and be replacing fossil fuel heating. The limit is 45kWth for a single system, or 70kWth for several heat pumps together. Hybrids (heat pump plus gas boiler) are not eligible. Full rules on the commercial heat pumps page.
  • Public sector: the Public Sector Decarbonisation Scheme has funded public bodies in England replacing fossil fuel heating at the end of its life with low-carbon heat. Phase 4 applications closed on 25 November 2024. Its rules asked applicants to contribute at least the cost of a like-for-like fossil fuel replacement, and at least 12% of project costs. For loans and the current rounds, see Salix funding. A public building's Display Energy Certificate advisory report is a good place to start the case.
  • Charities and churches: see church energy grants and charity grants.
  • Local and devolved support: council business energy grants, Scotland, Wales and Northern Ireland, and the full list at business energy grants.

Tax relief. HMRC lists "a space or water heating system" as an integral feature. Under CA22340, if you spend more than 50% of the cost of replacing an integral feature, at once or within any 12 months, the spend is treated as capital expenditure on a replacement, not a repair. It counts as special rate expenditure, "although the taxpayer may be able to claim the AIA instead".

The Annual Investment Allowance is £1 million, so most businesses can write off a whole boiler replacement in year one. Companies spending above that can claim the 50% special rate first year allowance on plant bought new from 1 April 2023. Smaller repairs below the 50% line are usually a revenue cost. Confirm the treatment with your accountant.

When replacing your commercial boiler isn't the answer

  • The boiler is fine, the controls aren't. Plant starting at 4am, heating empty floors, or running all weekend wastes more gas than a few points of boiler efficiency. Fix the time and zone controls first. A business energy audit will show where the gas goes.
  • The building leaks heat. Roof insulation, draught-proofing and secondary glazing cut the size of whatever you fit next, boiler or heat pump. Our business energy saving guide covers the low-cost fixes.
  • You are about to change the building. A refurbishment, extension or change of use changes the heat load. Size the plant for the building you'll have, not the one you have now.
  • The real problem is hot water. Kitchens, care homes and leisure sites often have hot water loads that need their own plant. Replacing the space-heating boiler won't fix a failing calorifier.
  • A gas-for-gas swap without checking the alternative. If your building could take a heat pump, a new gas boiler commits you to gas, and to the levy changes above, for its whole life. Get both options priced on one survey before you decide.

Getting a commercial boiler replacement quoted

  1. Gather the facts: twelve months of gas bills, the boiler make, model, output and age, recent service reports, and how the building is used (hours, rooms, hot water).
  2. Get a heat-loss survey so the new plant is sized to the building, not the old boiler.
  3. Price two options on that survey: a compliant gas boiler replacement and a heat pump or hybrid.
  4. Run the running-cost method above with your own prices, and add tax relief and any grant.
  5. Plan the timing for summer if you can, with temporary heat arranged if the building can't go without.

Large companies can describe the replacement in the energy efficiency section of their SECR report.

Fill in the form and we'll pass your enquiry to one commercial heating installer who can price both options from the same visit. We're an independent service, not the government-owned Great British Energy, and we don't run any grant scheme.

Sources checked 20 November 2026

Great British Energy is an independent guide. We are not affiliated with Great British Energy, the publicly owned energy company (gbe.gov.uk), HM Government, Ofgem or OZEV. Scheme rules and budgets change, so confirm the current position with the scheme administrator before you commit spend. We may receive a fee from the installer we introduce you to.

Commercial boilers questions

What efficiency must a replacement commercial boiler meet?

In England, Approved Document L Volume 2 sets minimum seasonal efficiencies for boilers installed in existing buildings: 91% for a single gas boiler up to 400kW, 88% from 401kW to 2MW and 84% above 2MW. Single LPG boilers up to 2MW and single oil boilers should reach 93%. The 2026 edition, which takes effect on 24 March 2027, keeps the same figures.

Can I still install a gas boiler in a commercial building?

Yes, in an existing building, as long as it meets Part L's efficiency and controls rules. The Future Buildings Standard, in force from 24 March 2027, expects new non-domestic buildings to meet heating and hot water from low-carbon sources, with room for fossil fuel backup in buildings such as hospitals.

How much does a commercial boiler replacement cost?

There is no official price list. Cost depends on boiler output and number, the flue, plant room pipework and pumps, system cleaning, controls, access and removal of old plant, any gas supply upgrade and temporary heat. Ask installers to itemise those lines against the same heat-loss figure, and to price a heat pump option on the same survey.

How often should a commercial boiler be serviced?

The law says employers must keep gas appliances, pipework and flues at the workplace in a safe condition, without fixing an interval. HSE advises regular maintenance by a Gas Safe registered engineer, and annual servicing to the manufacturer's instructions is the usual way to show it. Where people live in the building under a lease or licence, the landlord must also have a gas safety check at least every 12 months.

Is there a grant for a commercial gas boiler?

No. Government grants go to low-carbon heating. The Boiler Upgrade Scheme pays £7,500 towards an air or ground source heat pump up to 45kWth in a business building in England or Wales, and public bodies can look at the Public Sector Decarbonisation Scheme. Hybrids with a gas boiler aren't eligible for the Boiler Upgrade Scheme.

Can I claim capital allowances on a new commercial boiler?

Usually yes. A space or water heating system is an integral feature. If you spend more than 50% of the cost of replacing it within 12 months, HMRC treats it as capital expenditure, which can be claimed under the £1 million Annual Investment Allowance. Check the treatment with your accountant.

Is a heat pump cheaper to run than a commercial gas boiler?

It depends on your prices and the heat pump's seasonal efficiency. A heat pump is cheaper to run when your electricity price divided by your gas price is less than the heat pump SCOP divided by the boiler efficiency. Use your own bill prices, including the Climate Change Levy, to check.

Get your site quoted properly

Two minutes now saves weeks of ring-rounds. Tell us about your site and we will introduce one suitable installer.

Get a free boiler replacement check →
Get a free boiler replacement check →